Best T1 DEAL Networking Questions Fastest Internet

Posts Tagged ‘split’

100 Mbps Connection.
One Ethernet Port coming into my room.

I have a homemade cantenna made out of a USB11 Network adapter. How can I split this usb cable to go to two laptops? I have a WGT54 wireless router but how can I connect my USB to it or convert my usb cable to Cat5? Help I cannot figure it out.

but why is my max download speed 38kb/s? shouldnt it be atleast 100kb/s? anyone know why? and how i could speed up my download speed?
i live about 6miles from my ISP. phone lines are good. and im in the middle of the line.

I have one cat5e wire coming into my house, I have cat5 ran to 8 rooms and want to split the main and have an equally strong signal of phone and dsl in the 8 locations, what device do I use to do such? I already have wireless but this is for future homeowners to be able to plug in at each room, and I also need to split the phone lines.

ciruit-ed.com The 8×8 LED Matrix is connected directly to the PIC microcontroller with no limiting resistors. This demo shows a complex fading process where the center and outside fade-in and fade-out opposite of each other.

ciruit-ed.com The 8×8 LED Matrix is connected directly to the PIC microcontroller with no limiting resistors. This demo shows a complex fading process where the center and outside fade-in and fade-out opposite of each other.

So i recently asked this question and it wouldn’t let me reply. But so lets say i have a CAT5 cable and want to split it to two continuous running cables but i cant put a router on it because i wont be able to configure it. Is this what a switch is for? I need something that can take a male end and put it into two female ends. That i can plug ethernet cords into. And it has to be something that i dint have to configure. And i know this is unorthodox but is it possible to split a CAT5 cable while its connected to the internet and then put on a new plug while it is still being juiced with internet. It is not carrying a (POE) charge. But is this possible? Any help at all would be helpful.

Thanks

i have a dlink dsl g604t wireless router one option was to buy an antenna that will reach the other house but then i found out that it was far too expensive i have another adsl modem if it is needed or can i have dial up some how connecting to the modem i have at the house where it is staying

I am looking to re-wire my house and replace the 35+ year old Co-axial cable and also run Cat6 networking at the same time.

My issue is that I know that when you split the cable you lose some of the signal strength and I know that I will have to split it at least 3 to 4 times to reach all the rooms in the house.

I know that you can put an amplifier on the line, but ive also heard that can cause as many problems as it solves.

With installing Cat6 though out the house, I can just install a 16 port switch in the main junction room and install the modem in there and then just use the data jacks to get internet access. If the signal is strong enough for the internet signal (cable modem), then it is fine for anything else that it will have to do.

End result is I want to be able to support Cable Internet in any room of the house via the co-axial jack if need be (since that requires the higher signal frequency).

So I need to know what my split limit it and if a amp will fix any signal loss w/o causing other problems.

Thanks

I have a modem/router that only has one ethernet port, but I need two one for computer the other for my Xbox. Is there a device that can do this?

I am going to buy a PS3 in the next week and i was just wondering about the internet connection. I don’t have wireless internet and so i didn’t know if a ethernet splitter would work to hook up the PS3 and still have the internet to my computer work?

The modem is a ZyXEL P-600 series with ethernet, DSL and Internet LED indicator. the ethernet is always blinking, DSL steady and internet with no indication. How can i split the modem signal wired to a desktop and wireless to my laptop?

Need to rewire a number of rooms in home. I plan to use a Cat5e patch panel down stream of NID and a ADSL splitter. Is it permissible to just run a single 5e cable from patch panel to the outlet boxes and connect a pair into a separate outlet for the single line phone and the other pairs for internet and LAN to another outlet.
There will be 5 sites, (3 in house and 2 in remote structures) Compound is spread out and concrete walls as well.

Song: Dance & electronic – 009 Sound System – Holy Ghost How to split file parts by size you want By orion310591@hotmail.com

I want to hardwire an internet radio and the modem has only one ethernet output which provides internet to my PC. Can I split or run the ethernet into a hub or distributor?

I’m very familiar with the winsock(api) send/recv functions, but it has a cap of 8192 bytes, and the data i need to send is larger than 8192 bytes.
So i was wondering if anyone could tell me the steps and procedures to split the data into lets say packets with chunks of data(1024 bytes maybe)
I don’t want any source code since i want to do this myself, but i need some guidance.
Thanks…
Its TCP Protocol…

I have a main computer with a modem which i ran an ethernet cable from upstairs to another computer which has the ethernet cable plugged into it and it gets internet. It is not connected to the actual cable or modem just the ethernet. I want to run an ehternet cable from that computer to my xbox. I cant use a wireless router because you have to hook those to a modem. how can i split the ethernet to my xbox.

After moving my grandpa’s slightly older but underused Dell desktop, I need to purchase a wireless router to hook up the modem to my other Dell computer on the den floor to receive the internet through the wireless router to my bedroom on the second floors. Which wireless routers are best?

I have an ethernet cable coming from a modem and I need to split it so that several computers can access the internet. This is not something that will be there permanently, so issues of privacy / file sharing / firewalls can be disregarded.

Switches seem to be considerably cheaper than routers. So will this work with just a switch or do I need a router?

I find it annoying when my mum goes on paltalk she gets all the bandwith and it is near impossible for me to go on. And she finds it annoying if I was already downloading something, and she can not go becouse it will be to slow. Is there a way were we always get the same slower but split speed? Eg so if we both are downloading something we would be downloading at the same speed, not first one gets all, seconds goes extremly slow.